国产欧美精品区一区二区三区

当前位置: 首页 - 新闻动态 > 行业资讯
舞台灯光设备进行操控时应注意
更新时间:2022-08-01
文章来源:/
阅读量:22
舞台灯光设备随着科技的发展也是越来越越来越智能,当然在操作舞台灯光设备的时候我们一定要小心,以防弄坏灯光设备,那么舞台灯光设备进行操控时应注意什么呢?
With the development of science and technology, stage lighting equipment is becoming more and more advanced and intelligent. Of course, we must be careful when operating stage lighting equipment to prevent damage to the lighting equipment. What should we pay attention to when operating stage lighting equipment?
一、在灯泡处于冷的状态下,去猛然间的推亮(满)灯光,结果就很可能会造成灯泡&濒诲辩耻辞;啪&谤诲辩耻辞;的一声爆碎;或是造成灯泡的钨丝熔断、正确的操作是:
1、 When the bulb is cold, push the light suddenly (full), and the result is likely to cause the bulb to "snap" and burst; Or the tungsten wire of the bulb is blown, and the correct operation is:
当灯泡是处在冷的状态下(开场前)时,将操控台的推子试探的只推起一点(常说的压光状态),使灯泡微亮,让其处在预热状态,使其受热均匀,同时也可以蒸发掉那些凝结在灯泡玻璃壳上的水分子,预热数分钟后,再推亮一点,再预热数分钟后,这个时候才可将灯光完全的推亮。
When the bulb is in a cold state (before the opening), push up the pusher of the console tentatively only a little (often referred to as the calendering state), so that the bulb is slightly bright, so that it is in a warm-up state, so that it can be heated evenly. At the same time, it can also evaporate the water molecules condensed on the bulb glass shell. After preheating for several minutes, push it on a little, and then preheat for several minutes, then the light can be completely pushed on at this time.
二、切忌将调光台的推子在推满的状态下,再去打开硅箱的电源。其结果和上述的结果就会相同,两样都是会损坏灯泡的。这个时候应该将调光台所有的推子处于关闭状态,在打开硅箱电源。
2、 Never turn on the power of the silicon box when the pusher of the dimmer is full. The result will be the same as the above results, both of which will damage the bulb. At this time, all the faders of the dimmer should be turned off and the power of the silicon box should be turned on.
叁、提醒各位切忌在开关设备时,将灯控台和硅箱电源的顺序颠倒了。开启电源时,要先打开灯控台的电源,再打开硅箱的电源的;而在关闭电源时,则要先关闭硅箱的电源,后关闭灯控台的电源。
3、 Remind you not to reverse the order of light console and silicon box power supply when switching equipment. When turning on the power supply, first turn on the power supply of the light console, and then turn on the power supply of the silicon box; When turning off the power, turn off the power of the silicon box first, and then turn off the power of the light console.
山东舞台灯光
四、切忌在灯泡推亮时,大动作摇晃灯具。灯泡的钨丝是会因此而断裂或脱落的。因为灯泡在点亮后,温度逐渐升高,钨丝也会相应地会变软,同时也会受到地心引力的影响,钨丝也就相应的下垂,若在此时大动作的去摇晃灯具时,也是要等到灯光完全冷却后方可拆卸的。
4、 Never shake the lamp with big movements when the bulb is turned on. The tungsten wire of the bulb will break or fall off because of this. Because after the bulb is lit, the temperature gradually rises, and the tungsten wire will correspondingly soften. At the same time, it will also be affected by gravity, and the tungsten wire will correspondingly sag. If you shake the lamp in a big action at this time, you can't disassemble it until the light is completely cooled.
五、山东舞台灯光厂家提醒您,不要在更换灯泡时,直接选择用手去接触灯泡,这是会影响灯泡的光洁度,而另一个隐性的危害是导致灯泡的爆碎、在更换灯泡时,一定会先戴上手套,再去接触灯泡的。而如果没有手套,也是可用包装灯泡的海棉、塑料纸或柔软的纸巾包裹,再进行安装,而在安装之后也是一定要记得将这些包裹物取下来,以免在推亮灯泡时会引发火灾。
5、 Shandong stage lighting manufacturers remind you not to directly choose to touch the bulb by hand when replacing the bulb, which will affect the smoothness of the bulb, and another hidden hazard is that it will cause the bulb to burst. When replacing the bulb, you must wear gloves first and then touch the bulb. If you don't have gloves, you can also wrap the bulb with sponge, plastic paper or soft paper towels before installation. After installation, you must remember to remove these packages to avoid fire when pushing the bulb on.
此外切忌将所安装灯光的功率超过了厂家所规定的功率,若是只考虑灯泡在熔断的瞬间所产生的电流的话,那是非常片面的看法。所以您在使用相关设备之前应该会有所了解的,更多信息就来我们网站获取吧。
In addition, the power of the installed light should not exceed the power specified by the manufacturer. It is a very one-sided view to consider only the current generated by the bulb at the moment of fusing. So you should know something before using relevant equipment. For more information, please come to our website Get it.

地址: 山东省济南市历下区崇华路金星龙盛大厦405

电话:18954185191

网址:/

贰-尘补颈濒:331365650蔼辩辩.肠辞尘

国产欧美精品区一区二区三区Shandong Wenguang Intelligent Technology Co., Ltd