由于家庭影院系统在音箱的安装、摆位以及调试等方面都有一套严格的规范，这意味着用户只有遵守这些规范来对音箱进行安装和调试才能得到理想的声音。下面为大家介绍国产欧美精品区一区二区三区的设置与总调试内容。
Because the home theater system has a set of strict specifications in the installation, positioning and debugging of speakers, it means that users can get ideal sound only by following these specifications to install and debug speakers. Now let's introduce the setting and general commissioning of the speakers in the home theater.
音箱的设置与摆放
Setting and placement of speakers
超低音音箱主要用来弥补主音箱低频下限的不足。同时还可以增加低频能量。因此，消费者在使用前必须设置好功放的低频分频点。设置分频点时，应根据您选择的音箱系统进行设置。
The subwoofer is mainly used to make up for the deficiency of the low frequency lower limit of the main speaker. At the same time, it can also increase the low-frequency energy. Therefore, consumers must set the low-frequency division point of the power amplifier before use. When setting the frequency division point, it should be set according to the speaker system you select.
与其他音箱系统一样，您必须根据每个音箱系统的低频响应设置每个通道的分频点。分频点设置好后，就可以定位音箱了。理论上，音箱可以放置在房间的任何地方。
Like other speaker systems, you must set the frequency division point of each channel according to the low-frequency response of each speaker system. After the frequency dividing point is set, the speaker can be positioned. In theory, speakers can be placed anywhere in the room.
但实际上，消费者需要尝试将音箱放在房间内的不同位置进行聆听，找出佳放置点。一般情况下，消费者可以将音箱放在前面。
But in fact, consumers need to try to put the speakers in different positions in the room to listen and find out the best place to put them. In general, consumers can put the speaker in the front.
音箱系统的总调试
General commissioning of speaker system
音箱系统系统的整体调试，测量每个音箱系统与人耳的距离（一般为高音喇叭与人耳的距离），将测得的距离值输入功放。然后消费者在听音位置使用声压计测量各声道的输出声压，并根据读数独立调节础痴功放中各声道的输出电平，使各声道的声压达到80诲叠参考声压值。然后音箱系统设置基本完成。
For the overall commissioning of the speaker system, first measure the distance between each speaker system and the human ear (generally the distance between the tweeter and the human ear), and input the measured distance value into the power amplifier. Then the consumer uses a sound pressure meter to measure the output sound pressure of each channel at the listening position, and independently adjusts the output level of each channel in the AV power amplifier according to the reading, so that the sound pressure of each channel reaches the 80dB reference sound pressure value. Then the speaker system setting is basically completed.
完成以上两步后，其实对于大家粉的普通消费者来说，基本的调试就可以认为已经完成了。不过对于一些追求更好效果的消费者来说，建议使用均衡器来校正房间的频响曲线。
After completing the above two steps, in fact, for ordinary consumers, the basic debugging can be considered to have been completed. However, for some consumers seeking better results, it is recommended to use an equalizer to correct the frequency response curve of the room.
为什么要这样做？厂家认为主要原因是大部分消费者的听音环境的频响曲线并不理想。当然，也有人认为加均衡器会影响音质，但如果房间的频响曲线不理想，就会严重影响整体声音平衡，从而导致整体音效变差。因此，在相对不理想的聆听环境中，使用均衡器是一个不错的选择。
Why? Home theater speaker manufacturers believe that the main reason is that the frequency response curve of most consumers' listening environment is not ideal. Of course, some people think that adding an equalizer will affect the sound quality, but if the frequency response curve of the room is not ideal, it will seriously affect the overall sound balance, resulting in poor overall sound effect. Therefore, it is a good choice to use equalizer in a relatively poor listening environment.
还有一点要注意的是，消费者必须利用自己熟悉的软件，并通过自己实际的听感对音箱系统进行不断的调整，这样才能得到理想的效果。更多对于该产物的相关信息就来我们网站咨询了解吧！
Another thing to note is that consumers must use their familiar software and constantly adjust the speaker system through their actual listening sense, so as to get the ideal effect. For more information about this product, please visit our website at www.wenguangzhining Www. 68mn!
